Matrix: What are the ECS configuration options for the E-QUE card?
E-QUE Cards can be configured in Median and Omega frames for the following options:Each card has 2 E1/T1 transceiver drivers.E1 is a 2Mb data line with 32 channels (64 channels per E-QUE card) T1 is 1.54Mb data line with 24 channels (48 channels per E-QUE card)
• E-QUE (E1 Direct) - This action automatically adds an E-QUE card configured for 60 direct ports using E1 protocol.Each E1 port (30 channels) can be used as an E1 communication line to another E1 device.
• E-QUE (E1 Trunk) - An E-QUE card set to E1 Trunk is used to connect Eclipse matrices using E1 trunking protocol. The System Ports display will show two ports numbered 1 and 31. Each port carries 30 channels
• E-QUE (T1 Trunk) - An E-QUE card set to T1 Trunk is used to connect Eclipse matrices using T1 trunking protocol. The System Ports display will show two ports numbered 1 and 25. Each port carries 24 channels
• E-QUE (Antenna) - This action automatically adds an E-Que card with eight antenna ports configured. 8x CellCom/FreeSpeak antennas can be directly connected to the E-QUE rear card. Each must be locally powered antennaEach antenna can support upto 5 beltpacksEach antenna will be shown as having six ports (five ports for beltpack data and one port for antenna to matrix comms)
• E-QUE (Splitter) - This action automatically adds an E-Que card with ten antenna ports configured.10x CellCom/FreeSpeak antennas can be connected via two splitter units (each splitter can drive 5x antennas). The splitter units are connected to port 1 and 5 on the E-QUE rear card. card. Each splitter must be locally powered. Antennas can be powered either be locally powered or powered down the line.Each antenna can support upto 5 beltpacksEach antenna will be shown as having six ports (five ports for beltpack data and one port for antenna to matrix comms)
In order to access these options in ECS select setup matrix hardware / physical hardware and select an empty card slot for the E-Que card and then select the desired E-QUE card option for the empty slot. Once the E-QUE card is inserted into the frame select apply changes to the frame with a frame reset to bring the card on-line.
• E-QUE (E1 Direct) - This action automatically adds an E-QUE card configured for 60 direct ports using E1 protocol.Each E1 port (30 channels) can be used as an E1 communication line to another E1 device.
• E-QUE (E1 Trunk) - An E-QUE card set to E1 Trunk is used to connect Eclipse matrices using E1 trunking protocol. The System Ports display will show two ports numbered 1 and 31. Each port carries 30 channels
• E-QUE (T1 Trunk) - An E-QUE card set to T1 Trunk is used to connect Eclipse matrices using T1 trunking protocol. The System Ports display will show two ports numbered 1 and 25. Each port carries 24 channels
• E-QUE (Antenna) - This action automatically adds an E-Que card with eight antenna ports configured. 8x CellCom/FreeSpeak antennas can be directly connected to the E-QUE rear card. Each must be locally powered antennaEach antenna can support upto 5 beltpacksEach antenna will be shown as having six ports (five ports for beltpack data and one port for antenna to matrix comms)
• E-QUE (Splitter) - This action automatically adds an E-Que card with ten antenna ports configured.10x CellCom/FreeSpeak antennas can be connected via two splitter units (each splitter can drive 5x antennas). The splitter units are connected to port 1 and 5 on the E-QUE rear card. card. Each splitter must be locally powered. Antennas can be powered either be locally powered or powered down the line.Each antenna can support upto 5 beltpacksEach antenna will be shown as having six ports (five ports for beltpack data and one port for antenna to matrix comms)
In order to access these options in ECS select setup matrix hardware / physical hardware and select an empty card slot for the E-Que card and then select the desired E-QUE card option for the empty slot. Once the E-QUE card is inserted into the frame select apply changes to the frame with a frame reset to bring the card on-line.
CAN'T FIND YOUR ANSWER? CLICK HERE TO CONTACT SUPPORT
This solution was provided to you by Clear-Com via a question submitted to us by customers like you. If your question wasn’t answered, you need help or you have a recommended solution for our database, please send us an email at support@clearcom.com
The information on this page is owned by Clear-Com and constitutes Clear-Com’s confidential and proprietary information, may be used solely for purposes related to the furtherance of Clear-Com’ business and shall not be disclosed, distributed, copied or disseminated without Clear-Com’s prior written consent. Click Here for Clear-Com's privacy statement.