Which CAT5e , CAT6, cable should I use
Data from : https://www.patchcordsonline.com/cat5-vs-cat6
Clear-Com recommends using CAT5e or higher for most 100Mb based network installs (Helixnet, LQ, EHX PC, Eclipse HX Matrix to Matrix CPU comms )
Clear-Com recommends using CAT6 or higher for 1Gb based network installs (AES67/ ST2110-30 networks)
There are a few different "categories" of Ethernet cable available today. Each one has different capabilities, but the most important is the supported transmission speed. The table below summarizes the differences between the current standards.
Cable Category | Maximum Length | Transmission Speed |
|---|---|---|
Cat 5 | 100 Meters | 0.1 Gbps |
Cat 5e | 100 Meters | 1 Gbps |
Cat 6 | 100 Meters | 1 Gbps |
Cat 6A | 100 Meters | 10 Gbps |
Cat 7 | 100 Meters | 10 Gbps |
Cat 8 | 30 Meters | 40 Gbps |
All categories of cables are available today (except Cat 5), so the big debate is about what type or "category" of cable to use to give the best performance. It's not an easy decision, so we have outlined the differences below:
Cat 5
We are only mentioning this type for historical purposes; the maximum transmission speed was only 100 Mbps. Outstanding performance in 1995, now not so much.
Cat 5 cable is no longer produced, mainly due to its lack of performance, being superseded by the Cat 5e standard.
Cat 5e
Today, this is one of the most widely used standards. Cat 5e cable is capable of performing up to 350 Mhz and capable of speeds up to 1 Gbps.
The "e" stands for enhanced; the "enhancement" is due to a better design that significantly reduces cross-talk over the older Cat 5 standard.
As you can see the answer to one of the most asked questions is YES Cat 5e is capable of 1 Gbps networking!
Cat 6
The Cat 6 standard gives higher performance than Cat 5e. Cat 6 can perform up to 550 Mhz, and like Cat 5e is designed for 1 Gbps networking.
So this is where there is a large amount of debate, if both the Cat 5e and Cat 6 standard are designed to support the same speed then what's the real difference? As we just mentioned, the Cat 6 standard supports higher frequencies, and this means that it can provide that Gigabit speed more reliably and efficiently.
So what does that mean? If you had a 100 meter run of both Cat 5e and Cat 6 in the same environment, the chances are that the Cat 6 cable run would run at 1 Gbps more consistently. It is for this reason that it is recommended to use Cat 6, it is more "future proof" than using Cat 5e.
Cat 6A
This standard is the next evolution of the Cat 6 type described above. The "A" is for augmented (no, there was not a Cat 6e standard). Cat 6A has a significant performance increase over Cat 6, designed for 10 Gbps networking.
There is not an increase in supported frequency (Mhz), but the construction of the cable significantly reduces cross talk of all types allowing much larger bandwidth.
Cat 6A is still a copper, twisted pair cable using RJ45 connectors, so yes you can use it in your home network, but that would be a costly decision. Even today, there are not that many 10 Gbps interfaces for home devices.
Cat 7
The Cat 7 standard has even stricter specifications than Cat 6A and unlike all the previous categories does not come in an unshielded variant.
Cat 7 supports 10 Gbps networking just like Cat 6A but is seen to produce more reliable results, mainly due to its double-shielded construction.
Additionally, this standard wasn't recognized by the TIA/EIA organizations.
Cat 8
Cat 8 is for data center applications, primarily designed to interconnect switches, servers, blade chassis, etc. The standard has two classes:
Class I (Cat 8.1) - Meant to be used with 8P8C RJ45 connectors
Class II (Cat 8.2) - Meant to be used with Tera or GG45 connectors
The advantage of using copper over fiber in the cases mentioned above is that copper devices are more energy-efficient than their fiber counterparts. A definite advantage for data center providers seeking power and cooling savings.
Below is the Chinese translation:
我应该使用哪一种CAT5e , CAT6类电缆
数据来源:https://www.patchcordsonline.com/cat5-vs-cat6
Clear-Com推荐使用CAT5e或更高版本,用于大多数100Mb的网络安装(Helixnet, LQ, EHX PC, Eclipse HX Matrix to Matrix CPU通信)
Clear-Com建议使用CAT6或更高版本的1Gb网络安装(AES67/ ST2110-30网络)
今天有几个不同的“类别”的以太网电缆可用。每一个都有不同的能力,但最重要的是所支持的传输速度。下表总结了现行标准之间的差异。
电缆类别
最大长度
传输速度
Cat 5
100米
0.1 Gbps
Cat 5e
100米
1 Gbps
Cat 6
100米
1 Gbps
Cat 6A
100米
10 Gbps
Cat 7
100米
10 Gbps
Cat 8
30米
40 Gbps
今天所有种类的电缆都可以使用(Cat 5除外),所以大的争论是使用哪种类型或“类别”电缆才能提供最好的性能。这不是一个容易的决定,所以我们概括了以下的不同之处:
Cat 5
我们只是出于历史目的而提到这类;最大传输速度只有100mbps。1995年表现突出,现在不那么好了。
Cat 5电缆不再生产,主要是由于性能不足,被Cat 5e标准取代。
Cat 5e
今天,这是最广泛使用的标准之一。Cat 5e电缆的性能可达350 Mhz,速度可达1 Gbps。
"e"代表enhanced;“增强”是由于一个更好的设计,显著比老的Cat 5标准减少串音。
正如你所看到的,最常见的问题之一的答案是,是的,Cat 5e能够适用1 Gbps的网络!
Cat 6
Cat 6标准比Cat 5e标准提供更高的性能。Cat 6可以执行高达550 Mhz,而像Cat 5e一样是为1 Gbps网络设计的。
所以这就是有大量争论的地方,如果Cat 5e和Cat 6标准都被设计为支持相同的速度,那么真正的区别是什么?正如我们刚才提到的,Cat 6标准支持更高的频率,这意味着它可以提供更可靠和有效的千兆速度。
这是什么意思呢?如果您在同一环境中同时使用Cat 5e和Cat 6跑100米,那么Cat 6电缆跑的速度可能会更一致地达到1 Gbps。正因为如此,我们推荐使用Cat 6,它比使用Cat 5e更具有“前瞻性”。
Cat 6A
该标准是上述Cat 6类型的下一个发展。 “ A”是增强型的(不,没有Cat 6e标准)。 与6类相比,Cat 6A的性能有了显着提高,专为10 Gbps网络而设计。
支持的频率(Mhz)并没有增加,但是电缆的结构显着减少了所有类型的串扰,从而允许更大的带宽。
Cat 6A仍然是使用RJ45连接器的铜质双绞线电缆,因此可以在家庭网络中使用它,但这是一个昂贵的决定。 直到今天,用于家庭设备的10 Gbps接口还不多。
Cat 7
Cat 7标准的规格比Cat 6A还要严格,并且与所有先前的类别不同,它不是非屏蔽的。
Cat 7与Cat 6A一样,支持10 Gbps网络,但是主要由于其双重屏蔽结构,它可以产生更可靠的结果。
此外,TIA / EIA组织未认可该标准。
Cat 8
Cat 8用于数据中心应用程序,主要用于互连交换机,服务器,刀片服务器机箱等。该标准分为两类:
•Class I(Cat 8.1)-意味着与8P8C RJ45连接器一起使用
•Class II(Cat 8.2)-意味着与Tera或GG45连接器一起使用
在上述情况下,使用铜而不是光纤的优点是铜器件比光纤更节能。 对于寻求节电和散热的数据中心提供商来说,这是绝对的优势。