/
Broaman: Can the Optocore MUX-22 be used to connect the NEW Freespeak II 2 Splitters (FSII-SPL) to the Base?
Broaman: Can the Optocore MUX-22 be used to connect the NEW Freespeak II 2 Splitters (FSII-SPL) to the Base?
- Administrator
Owned by Administrator
Apr 06, 2019
It is possible to use the Optocore MUX-22s AUX ports to send the FS-II FSII-SPL splitter fiber across. It is also possible to connect 2x FSII-SPLs over the MUX-22s AUX ports.
For this to work the single mode SFPs, HLI-SMFO must be used. If other SFPs are used the wavelength must be 1310.
Be sure to turn off dip switch 6 to activate local sync on on the FSII-SPL splitter that is remote from the base.
See Example setup below
1. On the bottom MUX-22 AUX port connect a fibre patch cable to the FSII BASE2 antenna-fiber port. (make sure the FSII Base SFP = single mode @ 1310)
2. on the top / remote MUX-22 AUX port connect a fibre patch cable to the FSII-SPL antenna-fiber port. (make sure the FSII-SPL SFP = single mode @ 1310) connect . Set the FSII-SPL to generate local sync to the remote antennas
The MUX-22s are connected and programmed as usual:
The fibers for the splitter(s) are routed through the AUX ports:
For this to work the single mode SFPs, HLI-SMFO must be used. If other SFPs are used the wavelength must be 1310.
Be sure to turn off dip switch 6 to activate local sync on on the FSII-SPL splitter that is remote from the base.
See Example setup below
1. On the bottom MUX-22 AUX port connect a fibre patch cable to the FSII BASE2 antenna-fiber port. (make sure the FSII Base SFP = single mode @ 1310)
2. on the top / remote MUX-22 AUX port connect a fibre patch cable to the FSII-SPL antenna-fiber port. (make sure the FSII-SPL SFP = single mode @ 1310) connect . Set the FSII-SPL to generate local sync to the remote antennas
The MUX-22s are connected and programmed as usual:
The fibers for the splitter(s) are routed through the AUX ports:
, multiple selections available,
Related content
Wireless: What type of SFP does the new FSII-SPL (splitter use)
Wireless: What type of SFP does the new FSII-SPL (splitter use)
More like this
WIRELESS: SFP For Single Fibre Cable on FSII-BASE-II to FSII-SPL
WIRELESS: SFP For Single Fibre Cable on FSII-BASE-II to FSII-SPL
More like this
Wireless: Can I extend / remote the antennas on the DX-210 base station?
Wireless: Can I extend / remote the antennas on the DX-210 base station?
More like this
FSII-BASE-II Firmware Update Guide
FSII-BASE-II Firmware Update Guide
More like this
WALKIE TALKIE TO FREESPEAK II BASE-II CONFIGURATION VIA CCM
WALKIE TALKIE TO FREESPEAK II BASE-II CONFIGURATION VIA CCM
More like this
Wireless: Can I combine DX210 antennas with other non 2.4 GHz antenna systems?
Wireless: Can I combine DX210 antennas with other non 2.4 GHz antenna systems?
More like this
CAN'T FIND YOUR ANSWER? CLICK HERE TO CONTACT SUPPORT
This solution was provided by Clear-Com via a question submitted to us by customers like you. If you wish to share with us a new solution or update an old one, please follow this link..
The information on this page is owned by Clear-Com and constitutes Clear-Com’s confidential and proprietary information, may be used solely for purposes related to the furtherance of Clear-Com’ business and shall not be disclosed, distributed, copied or disseminated without Clear-Com’s prior written consent. Click Here for Clear-Com's privacy statement.